Clik here to view.
Short on RAM? Overcommit
@ndo wrote: Hi all Just thought that I would share this with you. I've been hitting a wall with the specs of my machine, so I really needed to overcommit on the RAM I had available. Here how you do...
View ArticleClik here to view.
Change Default Flat and Flat1 ranges
@allm wrote: I've read a few articles posted on this but nothing solid for a solution. I have a new install of VIRL on ESXi, I have overlapping subnets with the default installation of VIRL and...
View ArticleGuest VM - Unable to save configuration state
@GarethMorrison wrote: HiI'm trying to provision a guest VM within VIRL (an F5 VE). I've successfully created a subtype for the VM and managed to get it to boot up within VIRL, configured a management...
View ArticleMigrate servers and license key
@kbreit wrote: I am doing a fresh install of VIRL on a new server and need to migrate the license key. How can I do this? Posts: 4 Participants: 2 Read full topic
View ArticleFlat, what is that?
@Nadeem_Rafi wrote: Hi, I have esxi virl installation, this installation uses standard flat and flat 1 network. My live network is connected at 192.168.2.0/24, how i can connect virl machines with my...
View ArticleChange sw load on switch?
@duckshot wrote: Hi, I can't find where the process is described to convert the switch IOS load to the same SW I'm running on my 7609 switches. Thank you Posts: 1 Participants: 1 Read full topic
View ArticleJoining existing VMs to VIRL projects
@pcpaulh wrote: Hi all, I thought I had grasped the whole FLAT and FLAT1 networks principle but I am still struggling.I am trying to give an existing virtual machine connectivity to my VIRL...
View ArticleIOSvL2 Not Listed as an avilable Image on VIRL Server
@joe88f wrote: Ive done the upgrade numerous times to ensure I did not miss a step. Maestro shows IOSvL2, but I get image not found.On my VIRL server under software IOSvL2 is not listed.I am running...
View ArticleVIRL- Telnet connection time out
@Magreth wrote: Hi, I am using VIRL bare-metal installation in DELL PowerEdge T610, and connecting to it using VM Maestro from my Windows 8.1 laptop. I am following this tutorial, and everything went...
View ArticleAutnetkit not visualizing
@joe88f wrote: When I launch autnetkit nothing is seen. I can't use the pulldown either. Overlay is the only thing I see, nothing else. For all topologies.When I launch from outside VMM to port 19401...
View ArticleNexus 5k and fexes
@dentifrice wrote: Hi, I've been talking to you guys at CiscoLive and I asked a question about Nexus 5k and fexes images. So I'm asking it here again officially if that can speed up the process :...
View ArticleVirtual PCs (VPCS)
@William_Foster wrote: Has anyone got Virtual PCs working with VIRL? I'd love to use this rather than the server node because it has an easier configuration and lower resource usage. Posts: 3...
View ArticlevWAAS support?
@Beck wrote: Hi, are there any plans to integrate vWAAS appliances into VIRL? Many thanks, Gero Beck Posts: 1 Participants: 1 Read full topic
View ArticleIOS_L2 interface numbering
@srsheely wrote: This is a write up for the OCD and included a question for the dev team. I was playing in the uwadmin and changed the numbering scheme on the interfaces for a L2 node to feel more...
View ArticleUnable to use unmanaged switches
@Inderjit_Singh wrote: I just connected two unmanaged switches and when launching the simulation gets errorNo VM nodes of VIRL file. At least one VM node is required in the topology. I tried adding an...
View ArticleI purchased VIRL in Jan just installed 6/11/15
@matt wrote: I purchased VIRL in January 2015.I am just getting around to installing. I am up to checking Salt Status and resetting the license and it fails...aHow do I obtain a new license? Posts: 1...
View ArticleClik here to view.
License Error - Nodes
@allm wrote: Can anyone tell me if this is expected behavior? Can't imagine that there is a limit of seven nodes to a simulation when the samples come with about double the nodes. Screen Shot...
View ArticleValidation Rules menu not available
@Odell_Green wrote: After upgrading my VIRL to the latest version, and following the online tutorial, I am not able to locate the validation menu on the property pane next to the "Topology" choice....
View ArticleFailed to connect to curlmyip.com port 80: Connection refused
@neilclark wrote: Hi Guys, I have VIRL installed on my windows machine and i am running it in VMWare Player, I am following the instructions and am not able to complete the curl command i receive the...
View ArticleVIRL ASAv and IOSvL2 Question
@ipv4freely wrote: Hey guys, So I have the latest VIRL installation up and running on an ESXi server (0.9.250) and I am looking at running the ASAv in a simulation. This shows that I have the image...
View Article
/fit-in/580x348/filters:format(webp)/english-betterindia/media/media_files/2026/09/17/balaghat-4-2026-09-17-19-01-31.png)
