Download link for previous version
@knolf wrote: Can you please provide me a download link again for the version before 1.0.0. I lost already 3 complete days trying to get 1.0.0 installed ( clean install ). I get all sort of random...
View ArticleDefault Gateway via DHCP on FLAT network [VIRL 1.0.0]
@laurentprat wrote: Hi, When using Management Network type shared flat network, the nodes in the topology get an IP address in the 172.16.1.0/24 network but no Default Gateway is assigned which should...
View ArticleLaunch simulation failure
@dwinder wrote: Hello All,I'm new to VIRL, less than 24hrs post install and following along the tutorial, Exercise 6. On launching the simulation I get a failure notification > "Launch aborted as...
View ArticleConfiguring NAT Lab
@kcohne wrote: As part of a lab I have configured NAT on a router. I can not seem to get it to work. When doing show nat commands or debugs I get no output. It does not seem to be trying to translate...
View ArticleVIRL 1.0 Telnet to Console missing
@jwhiteitd wrote: I created a new server for VIRL 1.0, and it appears that the "Telnet to Console" is now missing. When I launch the same config on the old server (and using the updated version of VM...
View ArticleNX-OS Slow boot times
@jwhiteitd wrote: I've noticed that my NX-OS images take approximately 25-30 minutes to boot. I am also running Servers and ASAv images, which are booted after a few minutes. They all switch to Active...
View ArticleClik here to view.
How to find which folder image is located in virl?
@yam wrote: I can see the ASAv image under the Images>Other available images however i can not see that on the nodes? How can i make asa available as node to create topology? Pasted image997x473...
View ArticleWorkspace Manager Down
@allm wrote: Just getting this going and trying to activate the instance. I get to the web interface but when trying to go into the User Workspace Management and it times out. Looking at the health I...
View ArticleAutonetkit - how to disable BGP completely and assign interfaces to...
@avahiri wrote: Hi All, I'm trying to set up quite basic lab involving multi-area OSPF. Since I don't need BGP at all, I'd like to force the Autonetkit not to generate BGP config at all. What is the...
View ArticleClik here to view.
Multi-Area IS-IS Topology, no Attached Bit set from L1/L2 Router
@CurtisJTroabugh wrote: So, first I should mention I am brand new to IS-IS, so I may be misunderstanding exactly what the configuration should be. The issue: L1/L2 routers that have connections to...
View ArticleClik here to view.
VM Maestro Issues after compter crash
@CurtisJTroabugh wrote: I have been getting the following error when starting VM Maestro after a really ungraceful shutdown. At first none of my project appeared in my workspace. I was able to import...
View ArticleIosv missing after upgrade & No dest file found
@dchan wrote: Any ideas?log.txt (20.6 KB) Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Cannot load VIRL software tab in UWM
@jean_christophe wrote: When trying to load the "VIRL Software" tab from chrome accessing the VIRL VM/UWM from outside VIRL VM: Cannot load VIRL software tab.jpg1590x304 110 KB The salt status leads...
View ArticleSubscription Renew Issue
@sarithhom wrote: Hi Virl Team,I have tried to renew the subscription. But I had confusion to select the academy Gift Card. So, can I revert to my annual subscription renewal? Thanks, Sarith, Posts: 1...
View ArticleIOSv switches crash after building Etherchannels
@Calvin_Christopher wrote: Hello everyone and thank you for taking time to read this post. Each time I try to build an etherchannel between two IOSvL2 device, the switches involved crash and lose...
View ArticleUnable to run IOS-XRvs simultanosly
@ciscoaddict wrote: Hi all, I've setup a sample topology consisting of only 2 XRvs. When I start the simulation both routers are displayed as active but Ican telnet to one of them only. Telnet session...
View ArticleMigrate custom node images to new VIRL environment
@Keith_Olsen wrote: Hello, I have a couple of node images that I've created into my 0.9x VIRL environment, and would like to move these to the new 1.0.0 install. Is there a documented process to...
View ArticleClik here to view.
Only half my devices start and have telnet
@Minit55 wrote: I have a very strange issue. I´m int the pert 5 of the beginners guide. (just to give more info, i just installed VIRL for the first time last night). Im running VM workstation...
View ArticleWhy is there no option to SSH into the LXC from the FLAT
@Vic563 wrote: Hi, When login into any of the LXC why is there no option to SSH into the LXCs from the FLAT network. As you can see below I can SSH into the LXC to the LAN network segment where my...
View ArticleDocker Image Import
@hub wrote: I'm having trouble adding Docker images. I export them using docker save and go to upload the resulting tar file and I get an error. "Failed to import docker image:" Anyone have any...
View Article