Laptop WiFi bridged interface vmnet0
@Brian_Chostner wrote: I have VIRL on my laptop and it works great on my home network where I can bridge and get a predictable second IP address for VIRL eth0. When I leave home and go to work they...
View ArticleMac address-table static xxxx.xxxx.xxxx vlan 10 drop does not work for iosL2v
@ramirezcyrus wrote: I was wondering if the below command will work on VIRL... mac address-table static xxxx.xxxx.xxxx vlan 10 drop I attempted the above in global config mode. The below command I did...
View ArticleHaving an issue booting multiple CSR1000v?
@Vic563 wrote: Hi, I am trying to boot 10 CSR1000v and they never complete the boot process. However, if I boot IOSv they boot fine. Even if I boot 10 IOS-XR routers they boot up fine. What info do...
View ArticleClik here to view.
INE CCIE SP topology issues
@nate wrote: Hello everyone, i am having an issue where some nodes go into "shutoff" state as i am trying to load the INE CCIE-SP topology, here are some example pictures of this happening. here are...
View ArticleCall has Timed out--- Failed to connect to Salt Master
@raul.garcia wrote: I am getting now after a month or so Call has timed out ; failed to connect or minion key not accepted. If I run the System Status Diagnostics all check pass except the following:...
View ArticleClik here to view.
Telnet to console port
@Phoenix wrote: Hi!VIRL 1.0 was installed for me on ESXi. I configured everything and my topology starts successfully.However, I don't see the option "Telnet to console port" (screenshot attached)How...
View ArticleDirect Bank Transfer (Please add a fee of $35)
@leofalconi wrote: I don't have a credit card but i have the account bank...I would know because i should add $35 for the purchase.Thanks you for your answer.Leonardo Posts: 1 Participants: 1 Read...
View ArticleSalt Server Connection proble,
@txpatel wrote: I am Trying to activate my license, but I am getting "failed to collect current salt contact status:cisco contact was not establish. Posts: 1 Participants: 1 Read full topic
View ArticleHardware Specs for Maxed 30 Node topology
@CurtisJTroabugh wrote: It is time for me to build a new workstation as my old third gen i7 just isn't cutting it anymore. Since VIRL is pretty much the most resource hungry thing I run I have been...
View ArticleCan not start ASAv and NXOSv
@mbhatti1986 wrote: I have bought VIRL personal edition couple of weeks ago and exploring the platform. I am having issue with starting ASAv and NXOSv. When i checked the user workspace management...
View ArticleSecurity Onion on VIRL installation guide
@jobstfel wrote: How to run Security Onion in VIRL topologyThis tutorial will show you how to install and configure the Security Onion distribution (for intrusion detection, network security...
View ArticleCreating hosts in VIRL
@ramirezcyrus wrote: I'm attempting to connect hosts to switches so that I can do port security... How do I create a host in VIRL? Posts: 2 Participants: 2 Read full topic
View ArticleCCIE V5 features
@ramirezcyrus wrote: I think that features which are being tested in CCIE v5 need to be installed in VIRL. Such as WCCP, VSS, Private Vlans and etc.... Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
DHCP on Flat network
@bwang wrote: Screen Shot 2015-12-17 at 10.21.10 PM.png1628x1180 316 KB I follow this post: http://community.dev-innovate.com/t/disable-dhcp-for-the-flat-172-16-1-0-network/2479and disable dhcp on...
View ArticleClik here to view.
New virl-core v0.10.21.9 available
@csc wrote: Hi all, I have just seen there is a new version of VIRL-CORE available (v0.10.21.9): new_virl-core.png1067x174 17.2 KB I am just wondering if there is any information available on that...
View ArticleClik here to view.
VIRL 1.0.11 December'15 release - now available for download and upgrade
@jobstfel wrote: 18-Dec-15 VIRL December (virl.1.0.11) release is a minor upgrade building on the VIRL 1.0.0 release. NOTE - If you have VIRL 1.0.0 installed today, you can perform an in-place...
View ArticleClik here to view.
Interesting find while analysing disk usage
@NSI143 wrote: Seems legit Untitled.png816x672 83 KB Posts: 1 Participants: 1 Read full topic
View ArticleApply Script after Router Boot
@mkowalew3382 wrote: I found a bug in OSv were the netflow exporter source address is not honored if the simulation is stopped and restarted, although the configuration exists for each node. To work...
View ArticleFailed to start simulation
@Skmohanty wrote: Trying to lunch ostinato from my within company VPN. Works fine at home. Using the Youtube video on ostinato and used ip address 172.16.1.31 and 172.16.1.32. The router instantiates...
View ArticleSalt Issues?
@stevenjwilliams83 wrote: Are their any salt issues? I cannot get my version 1.0 to activate? Failed to collect current salt contact status: Cisco contact was not established. This may be temporary....
View Article